Every block. Free. Forever.

Six door CAD blocks in plan: 36in single swing, 72in double swing, 32in pocket, 48in bifold, 108in overhead garage and a roll-up.

Stairs, a mezzanine stair, an ADA ramp at 1:12, a handrail and a guardrail - five circulation CAD blocks whose dimensions are the code question.

Three window CAD blocks in plan: a 36in single-hung, a 60in double and a 72in slider.

Eleven plan-view sink and drinking-fountain CAD blocks, from a 17in hand-wash basin to a 96in three-compartment NSF warewashing sink.

Twenty-one plumbing pipe CAD blocks built from seven fittings - 45 and 90-degree elbows, tee, cross, cap, reducer and straight run - drawn in the orientations a run actually needs.

Water closet, wall-hung urinal, standard and ADA stall partitions, and a 36in grab bar - the five CAD blocks a toilet-room plan is assembled from.

Four drainage CAD blocks for the floor plan: a round floor drain, a square grated drain, a plain floor drain and a 120in trench drain.

Three bathroom CAD blocks: a 60x30in alcove bathtub, a 36in square shower stall, and the water heater that feeds them both.

Seven HVAC equipment CAD blocks: boiler, chiller, furnace, air handler, AC condenser, thermostat and a 48in fume hood.

Tee, cross, cap, transition and straight run - the HVAC duct CAD blocks that connect the elbows into a run.

The 45-degree and 90-degree HVAC duct elbow CAD blocks, each drawn in all four compass turns - northeast, northwest, southeast, southwest - so the fitting on the sheet points the way the run actually goes.

Twenty-seven electrical conduit CAD blocks: 45 and 90-degree elbows, tee, cross, cap, coupling, reducer, straight run and home run, each in the compass turns or axes it needs.

Six security CAD blocks covering both halves of a security drawing: the field devices - dome camera, bullet camera, access-control keypad - and the head end they report to, an alarm control panel, an NVR rack and a server rack.

Recessed can light, ceiling-mounted fixture, ceiling fan, floor lamp and table lamp - five lighting CAD blocks spanning the reflected ceiling plan and the furniture plan.

Duplex receptacle, 220V receptacle, single-pole light switch and the electrical panel they home run to - four electrical CAD blocks that carry most of a residential or light commercial power plan.

Twenty-two fire-sprinkler pipe CAD blocks across eight fittings: 45 and 90-degree elbows, tee, cross, cap, reducer, straight run and riser.

Pendant, upright and sidewall fire-sprinkler head CAD blocks - three physically different heads, not one symbol rotated three ways.

Emergency eyewash station, emergency safety shower and the combination unit that does both - three life-safety CAD blocks that get located by travel distance rather than by fitting the wall.

Fire alarm pull station, smoke and CO detector, and the fire extinguisher cabinet - three fire-protection CAD blocks that live on the device plan rather than the sprinkler sheet.

The exit sign and the emergency light - two CAD blocks that appear on the egress sheet of almost every commercial set.

Five P&ID equipment and symbol CAD blocks: centrifugal pump, tank or vessel, flange, reducer and instrument bubble.

Ball, check and gate valve CAD blocks in P&ID convention, all three on the same 24x12in body so a valve swap on the diagram does not move the line.

Two storage tank CAD blocks: a vertical tank shown as a 52in circle in plan and a horizontal tank at 144x48in.

Seven material-handling CAD blocks for the warehouse floor: 40x48 pallet, 48x40 IBC tote, selective pallet-rack bay, conveyor segment, platform scale, loading-dock leveler and an air compressor.

Seven storage and bedroom CAD blocks: 36in bookshelf, 60in dresser, 60in TV console, file cabinet, nightstand, bed and an office cubicle.

An 84in sofa, a 58in loveseat, an accent chair, a dining chair and an office desk with chair - five seating CAD blocks that cover both the living room and the workstation.

Refrigerator, dishwasher, range and cooktop - four kitchen appliance CAD blocks drawn at real cabinet dimensions, 24in for the dishwasher, 30in for the range, 36in for the fridge.

Dining table, conference table, a 48in desk and a reception desk - four table and desk CAD blocks running from a 48x24in workstation to a 158in conference top.

A 27in washing machine, a 27in dryer and the stacked pair - three laundry CAD blocks that all share the same 27in width, since the difference between a side-by-side and a stack is depth and closet, not face.

Six site CAD blocks for the paving and striping plan: standard parking stall, ADA stall with access aisle, ADA accessible-parking sign, sidewalk, driveway with apron and a bollard.

Fence, gate, retaining wall, storage shed, mailbox and bike rack - six site CAD blocks that define a property's edges and the small structures along them.

Four exterior CAD blocks: a rectangular swimming pool, a kidney-shaped pool, a deck and a patio.

A tree and a shrub - two landscape CAD blocks, both parametric on canopy radius, which is the only dimension a plant symbol really has in plan.